Fitting wallpaper in your home or office is the easiest and most effective way to improve the look of your place. Among the wall covering solutions, Prepasted wallpaper makes this entire process simpler. They reduce the need for that messy adhesive – just add water to activate the built-in paste for a hassle-free application
Today, we bring an easy step-by-step guide on how to hang Prepasted wallpaper. Whether it’s for bedroom wallpaper in home or office wallpaper, this 6-step easy guide will be the same.
6 Easy Steps To Hang Prepasted Wallpaper
This is your effective 6-step guide on hanging Prepasted wallpaper. Just follow the steps as instructed to get a flawless wall décor.
Gather Your Tools and Materials
Before you start, just make sure you have all the right tools and materials with you. If you have the following tools, the wallpaper fitting will become easier.
- A tape measure
- A pencil
- A level
- A utility knife or a pair of scissors
- A sponge for smoothing the wallpaper
- A bucket of water or a wallpaper trough
- A seam roller
- A step ladder
- Clean, dry towels
As for the materials, you only need the following two.
- Prepasted wallpaper rolls
- Painter’s tape to protect the edges and trims
With all the tools and materials, you are ready to start the wallpaper fixing.
Prepare the Walls
You need to do proper wall preparation if you wish your wallpaper to attach firmly to the walls and last a long time. Take care of the preparation step, especially when applying living room wallpaper, as this room’s décor serves as the focal point of the entire home. Start by wiping down its walls with a damp cloth. This will remove any dirt or grease from it. If needed, use mild, soapy water and let the walls dry before the actual preparation.
Now, if there are holes or cracks in it, just fill them with the spackle while sanding down the rough areas. Uneven walls tend to create bumps under the wallpaper, which ruins the final look. If the wall is highly absorbent, textured, or glossy, you should apply a primer to allow the wallpaper to adhere better. Use the level and pencil to draw vertical straight guidelines for where the first wallpaper strip will be attached. Now, these walls are ready for you to hang the wallpaper.
Cut and Activate the Wallpaper
Prepasted Wallpaper offers easy application, but you need to prepare each strip before you hang it. Measure the strip to the height of the wall and then add about 2 to 3 inches into the top and bottom before cutting it. This extra length will help with alignment and trimming later—cut the strips using scissors or a knife. Fill your wallpaper trough with clean water or you can also use the sponge and bucket method for activating wallpaper paste.
- For the wallpaper trough method, roll the wallpaper with the pattern inwards and submerge it for 30 seconds to activate the paste.
- For the sponge method, lay your wallpaper face down and take the damp sponge to evenly wet its back.
After using either method, gently fold the wallpaper with the pasted sides facing each other (without creasing) to allow the adhesive to activate evenly. Let it rest for 5 minutes. This step is very important, especially if you are doing kids’ room wallpaper or brick wallpaper. They have patterns and vibrant colors that need perfect alignment for a neat finish.
Hang the First Strip
You must correctly hang the first wallpaper strip, as it will set the tone for the rest of the wallpaper fitting. Unfold the top half of the strip and place it against the wall in the marked position. Leave a little bit of it overhanging from the top and the bottom. Use a smoothing brush to gently press on the wallpaper to attach it firmly to the wall. Work from the center to the outwards to remove the air bubbles. Once the top section is secure, you should continue smoothing the rest of the wallpaper in the same manner. Use the utility knife to trim the excess wallpaper from the ceiling and the baseboard sections.
In the case of installing kitchen wallpaper, we strongly recommend checking the walls first. They should be completely dry and free from any grease before applying that first strip of wallpaper. Clean walls ensure proper adhesive bonding and longevity of the wallpaper.
Hang Additional Strips
If you have a patterned wallpaper, align the strips carefully to each other to create a seamless look. Do not overlap the edges of the wallpaper, instead, keep the strips attached to each other at the edges to not leave any seams or gaps. Use the smoothing brush to securely press your wallpaper onto the wall to remove any bubbles or wrinkles. Use a roller over the seams to ensure the perfect bonding. Do not press too hard to squeeze out the adhesive.
Clean Up and Final Touches
Once all of the wallpaper is fixed, follow the last steps to ensure a polished look. First, take a damp sponge to wipe excess paste from the wallpaper surface before it dries. If the edges are lifting, press them down with a sponge or apply some water to reactivate the paste again. Let your wallpaper dry completely for about a day before you start decorating the room once more.
Conclusion
This is our guide on how to hang Prepasted wallpaper – this method of ours is effective for almost every living space wallpaper. When you follow the step-by-step instructions here, you will get a flawlessly fitted wallpapered space that improves your home decor. So grab your wallpaper rolls and start with the wallpaper fixing.
